Next: , Previous: Command Syntax, Up: Commands



3.2 Command Completion

gdb can fill in the rest of a word in a command for you, if there is only one possibility; it can also show you what the valid possibilities are for the next word in a command, at any time. This works for gdb commands, gdb subcommands, and the names of symbols in your program.

Press the <TAB> key whenever you want gdb to fill out the rest of a word. If there is only one possibility, gdb fills in the word, and waits for you to finish the command (or press <RET> to enter it). For example, if you type

     (gdb) info bre <TAB>

gdb fills in the rest of the word breakpoints, since that is the only info subcommand beginning with bre:

     (gdb) info breakpoints

You can either press <RET> at this point, to run the info breakpoints command, or backspace and enter something else, if breakpoints does not look like the command you expected. (If you were sure you wanted info breakpoints in the first place, you might as well just type <RET> immediately after info bre, to exploit command abbreviations rather than command completion).

If there is more than one possibility for the next word when you press <TAB>, gdb sounds a bell. You can either supply more characters and try again, or just press <TAB> a second time; gdb displays all the possible completions for that word. For example, you might want to set a breakpoint on a subroutine whose name begins with make_, but when you type b make_<TAB> gdb just sounds the bell. Typing <TAB> again displays all the function names in your program that begin with those characters, for example:

     (gdb) b make_ <TAB>

gdb sounds bell; press <TAB> again, to see:
make_a_section_from_file make_environ make_abs_section make_function_type make_blockvector make_pointer_type make_cleanup make_reference_type make_command make_symbol_completion_list (gdb) b make_

After displaying the available possibilities, gdb copies your partial input (b make_ in the example) so you can finish the command.

If you just want to see the list of alternatives in the first place, you can press M-? rather than pressing <TAB> twice. M-? means <META> ?. You can type this either by holding down a key designated as the <META> shift on your keyboard (if there is one) while typing ?, or as <ESC> followed by ?.

Sometimes the string you need, while logically a “word”, may contain parentheses or other characters that gdb normally excludes from its notion of a word. To permit word completion to work in this situation, you may enclose words in ' (single quote marks) in gdb commands.

The most likely situation where you might need this is in typing the name of a C++ function. This is because C++ allows function overloading (multiple definitions of the same function, distinguished by argument type). For example, when you want to set a breakpoint you may need to distinguish whether you mean the version of name that takes an int parameter, name(int), or the version that takes a float parameter, name(float). To use the word-completion facilities in this situation, type a single quote ' at the beginning of the function name. This alerts gdb that it may need to consider more information than usual when you press <TAB> or M-? to request word completion:

     (gdb) b 'bubble( M-?
     bubble(double,double)    bubble(int,int)
     (gdb) b 'bubble(

In some cases, gdb can tell that completing a name requires using quotes. When this happens, gdb inserts the quote for you (while completing as much as it can) if you do not type the quote in the first place:

     (gdb) b bub <TAB>

gdb alters your input line to the following, and rings a bell:
(gdb) b 'bubble(

In general, gdb can tell that a quote is needed (and inserts it) if you have not yet started typing the argument list when you ask for completion on an overloaded symbol.

For more information about overloaded functions, see C++ Expressions. You can use the command set overload-resolution off to disable overload resolution; see gdb Features for C++.

When completing in an expression which looks up a field in a structure, gdb also tries1 to limit completions to the field names available in the type of the left-hand-side:

     (gdb) p gdb_stdout.M-?
     magic      to_delete  to_fputs   to_put     to_rewind
     to_data    to_flush   to_isatty  to_read    to_write

This is because the gdb_stdout is a variable of the type struct ui_file that is defined in gdb sources as follows:

     struct ui_file
     {
        int *magic;
        ui_file_flush_ftype *to_flush;
        ui_file_write_ftype *to_write;
        ui_file_fputs_ftype *to_fputs;
        ui_file_read_ftype *to_read;
        ui_file_delete_ftype *to_delete;
        ui_file_isatty_ftype *to_isatty;
        ui_file_rewind_ftype *to_rewind;
        ui_file_put_ftype *to_put;
        void *to_data;
     }

Footnotes

[1] The completer can be confused by certain kinds of invalid expressions. Also, it only examines the static type of the expression, not the dynamic type.