12.5.4 Logical Operators
T1 = (bool)b; if (T1 == true) T1 = (bool)c; a = T1;
T1 in this example cannot be an expression temporary,
because it has two different assignments.
12.5.5 Manipulating operands
All gimple operands are of type
tree. But only certain
types of trees are allowed to be used as operand tuples. Basic
validation is controlled by the function
get_gimple_rhs_class, which given a tree code, returns an
enum with the following values of type
GIMPLE_INVALID_RHSThe tree cannot be used as a GIMPLE operand.
GIMPLE_BINARY_RHSThe tree is a valid GIMPLE binary operation.
GIMPLE_UNARY_RHSThe tree is a valid GIMPLE unary operation.
GIMPLE_SINGLE_RHSThe tree is a single object, that cannot be split into simpler operands (for instance,
This operand class also acts as an escape hatch for tree nodes that may be flattened out into the operand vector, but would need more than two slots on the RHS. For instance, a
COND_EXPRexpression of the form
(a op b) ? x : ycould be flattened out on the operand vector using 4 slots, but it would also require additional processing to distinguish
c = a op bfrom
c = a op b ? x : y. Something similar occurs with
ASSERT_EXPR. In time, these special case tree expressions should be flattened into the operand vector.
For tree nodes in the categories
GIMPLE_UNARY_RHS, they cannot be stored inside tuples directly.
They first need to be flattened and separated into individual
components. For instance, given the GENERIC expression
a = b + c
its tree representation is:
MODIFY_EXPR <VAR_DECL <a>, PLUS_EXPR <VAR_DECL <b>, VAR_DECL <c>>>
In this case, the GIMPLE form for this statement is logically
identical to its GENERIC form but in GIMPLE, the
on the RHS of the assignment is not represented as a tree,
instead the two operands are taken out of the
and flattened into the GIMPLE tuple as follows:
GIMPLE_ASSIGN <PLUS_EXPR, VAR_DECL <a>, VAR_DECL <b>, VAR_DECL <c>>
12.5.6 Operand vector allocation
The operand vector is stored at the bottom of the three tuple structures that accept operands. This means, that depending on the code of a given statement, its operand vector will be at different offsets from the base of the structure. To access tuple operands use the following accessors
Returns the number of operands in statement G.
Returns a pointer into the operand vector for statement
G. This is computed using an internal table called
gimple_ops_offset_. This table is indexed by the gimple code of
When the compiler is built, this table is filled-in using the sizes of the structures used by each statement code defined in gimple.def. Since the operand vector is at the bottom of the structure, for a gimple code
Cthe offset is computed as sizeof (struct-of
C) - sizeof (tree).
This mechanism adds one memory indirection to every access when using
gimple_op(), if this becomes a bottleneck, a pass can choose to memoize the result from
gimple_ops() and use that to access the operands.
12.5.7 Operand validation
When adding a new operand to a gimple statement, the operand will
be validated according to what each tuple accepts in its operand
vector. These predicates are called by the
gimple_<name>_set_...(). Each tuple will use one of the
following predicates (Note, this list is not exhaustive):
This is the most permissive of the predicates. It essentially checks whether t has a
Returns true if t is a "GIMPLE value", which are all the non-addressable stack variables (variables for which
is_gimple_regreturns true) and constants (expressions for which
Returns true if t is a symbol or memory reference whose address can be taken.
is_gimple_valbut it also accepts hard registers.
Return true if t is a valid expression to use as the function called by a
Return true if t is a valid minimal invariant. This is different from constants, in that the specific value of t may not be known at compile time, but it is known that it doesn't change (e.g., the address of a function local variable).
Return true if t is an
ADDR_EXPRthat does not change once the program is running.