17.10.4 Registers That Address the Stack Frame
This discusses registers that address the stack frame.
The register number of the stack pointer register, which must also be a fixed register according to
FIXED_REGISTERS. On most machines, the hardware determines which register this is.
The register number of the frame pointer register, which is used to access automatic variables in the stack frame. On some machines, the hardware determines which register this is. On other machines, you can choose any register you wish for this purpose.
On some machines the offset between the frame pointer and starting offset of the automatic variables is not known until after register allocation has been done (for example, because the saved registers are between these two locations). On those machines, define
FRAME_POINTER_REGNUMthe number of a special, fixed register to be used internally until the offset is known, and define
HARD_FRAME_POINTER_REGNUMto be the actual hard register number used for the frame pointer.
You should define this macro only in the very rare circumstances when it is not possible to calculate the offset between the frame pointer and the automatic variables until after register allocation has been completed. When this macro is defined, you must also indicate in your definition of
ELIMINABLE_REGShow to eliminate
Do not define this macro if it would be the same as
The register number of the arg pointer register, which is used to access the function's argument list. On some machines, this is the same as the frame pointer register. On some machines, the hardware determines which register this is. On other machines, you can choose any register you wish for this purpose. If this is not the same register as the frame pointer register, then you must mark it as a fixed register according to
FIXED_REGISTERS, or arrange to be able to eliminate it (see Elimination).
The register number of the return address pointer register, which is used to access the current function's return address from the stack. On some machines, the return address is not at a fixed offset from the frame pointer or stack pointer or argument pointer. This register can be defined to point to the return address on the stack, and then be converted by
ELIMINABLE_REGSinto either the frame pointer or stack pointer.
Do not define this macro unless there is no other way to get the return address from the stack.
— Macro: STATIC_CHAIN_INCOMING_REGNUM
Register numbers used for passing a function's static chain pointer. If register windows are used, the register number as seen by the called function is
STATIC_CHAIN_INCOMING_REGNUM, while the register number as seen by the calling function is
STATIC_CHAIN_REGNUM. If these registers are the same,
STATIC_CHAIN_INCOMING_REGNUMneed not be defined.
The static chain register need not be a fixed register.
If the static chain is passed in memory, these macros should not be defined; instead, the next two macros should be defined.
— Macro: STATIC_CHAIN_INCOMING
If the static chain is passed in memory, these macros provide rtx giving
memexpressions that denote where they are stored.
STATIC_CHAIN_INCOMINGgive the locations as seen by the calling and called functions, respectively. Often the former will be at an offset from the stack pointer and the latter at an offset from the frame pointer.
If the static chain is passed in a register, the two previous macros should be defined instead.
This macro specifies the maximum number of hard registers that can be saved in a call frame. This is used to size data structures used in DWARF2 exception handling.
Prior to GCC 3.0, this macro was needed in order to establish a stable exception handling ABI in the face of adding new hard registers for ISA extensions. In GCC 3.0 and later, the EH ABI is insulated from changes in the number of hard registers. Nevertheless, this macro can still be used to reduce the runtime memory requirements of the exception handling routines, which can be substantial if the ISA contains a lot of registers that are not call-saved.
If this macro is not defined, it defaults to
This macro is similar to
DWARF_FRAME_REGISTERS, but is provided for backward compatibility in pre GCC 3.0 compiled code.
If this macro is not defined, it defaults to
Define this macro if the target's representation for dwarf registers is different than the internal representation for unwind column. Given a dwarf register, this macro should return the internal unwind column number to use instead.
See the PowerPC's SPE target for an example.
Define this macro if the target's representation for dwarf registers used in .eh_frame or .debug_frame is different from that used in other debug info sections. Given a GCC hard register number, this macro should return the .eh_frame register number. The default is